[email protected] – https://www.g28carkeys.co.uk/fiat-car-key-replacements-near-me/

Reasons Your Fiat 500 Key Fob Won’t WorkA key fob for the Fiat 500 makes it simple to open doors and start your vehicle. However, there are G28 Car Keys could stop working. This includes a dead coin-battery, water damage, problems with the receiver modules, and interference.This listing is for a NEW replacement Fiat Flip Key Remote that is similar to the Ilco brand. It must be professionally programmed (click here to search for local locksmiths for your vehicle). It comes with trunk, lock and unlock buttons.Dead Coin BatteryThe most frequent reason why your 500 key fob won’t work is the battery is dead. Modern key fobs operate with a limited operating range, and must be within a few feet of the vehicle in order to function. If you’re far from your car and push the keyfob button it won’t respond and display the message “Key Fob Not Detected”.If this happens, replace the battery in the coin cell (Part number CR2032) with a new one from a trusted brand such as Panasonic, Duracell, or Energizer. You can usually find them at your local hardware store or on the internet.You can test the coin-cell battery by pressing the buttons while you are standing close to your Fiat 500. The parking lights should flash and the key fob will operate the lock and unlock switches.If your key fob does not work after replacing the battery, it might be water damage that hinders it from connecting to the module in your vehicle. Water damage can occur in many ways, including an easy splash or submerging the key fob into saltwater at the beach. If you suspect that your fob has been exposed to water, put it in a dry rice bag to pull the moisture out. If that doesn’t work the fob might need to be reset by an experienced auto locksmith or by the dealer.Water DamageWhile the fob has some rubber seals to keep water from the chip’s electronic circuit it, submerging it in the ocean or washing it in a machine could cause water damage. Saltwater can be particularly harmful to the circuit board of the fob, causing it to short out and eventually die. If you get the fob wet, it’s not an ideal choice but if you drop it into an empty cup of water, or forget to take it out of your pants pocket before running the washer, don’t give up hope.Remove the battery first. Clean the electronic chip using isopropyl alcohol or another similar product and then dry it thoroughly before replacing the battery. Test the fob next to determine if it’s functioning. If the key doesn’t work, it may need to be reprogrammed. This is usually done by an auto locksmith or dealer.If your key is old and has not been programmed for your car then you’ll need to replace it completely. A professional locksmith for automotive can complete this simple process. The locksmith will need the key to be cut to match the car’s ignition. The locksmith will also need to reprogram your fob into the car’s system. This is a cheap and quick process that can be completed on the same day.Receiver Module IssuesThe 500 key fob you have may not work because it’s out of range. The remote typically has a range of 30 feet or less and if it’s far away from your car it will not respond to your commands. This can easily be resolved by moving closer to your vehicle until it begins responding.If your fob does not work after you replace the battery for the coin, also called a “button”, “watch” or “button” It could be due to a problem with the circuit board inside. Reprogramming the fob is usually the solution to this problem. You can find instructions on how to do this for the majority of vehicles by searching YouTube or checking out the owner’s manual.It could be necessary to replace the metal clips that hold the coin batteries in their place. If they become loose, it can prevent your coin battery from sitting properly, causing your remote to malfunction.In rare instances the fob might become desync’d with your vehicle due to software or hardware issues. You can fix this issue by visiting your local dealer or auto-locksmith to reprogram your key fob. In certain instances they might need to reinstall the software on your body control module too.InterferenceInterference can also cause the key fob not to receive or transmit signals. This could occur if the keyfob is in close proximity to a radio transmitter like a cell phone or radar detector. Other reasons the key fob might not function could be due to a weak connection to the buttons or damage to the internal chip, or water damage.If the key fob been unable to function for a while out of the blue, or after trying everything you can do at home to solve it e.g. battery replacement, reprogramming and using the spare key fob, it could have a damaged receiver module on your 500. The receiver module, which is located under the dashboard, receives radio frequency signals from your key fob. It converts them to electronic commands that the vehicle interprets.There’s a quick and easy way to reset the 500’s internal system, including the keyfob. Disconnect the battery for 15 minutes by removing first the negative cable and then the positive cable. Reconnect the battery. This will erase any remaining electric current, and also restart the computer in your car. This can help you get your key fob working again. If the issue continues, you should seek the advice of an expert technician. They will be able to diagnose the exact cause of your problems.