inekd77@erus1.gemmasmith.co.uk – https://www.repairmywindowsanddoors.co.uk/patio-door-repairs-bexley/

Patio Door Lock RepairsOver time, patio door wear and tear can cause lock malfunctions. There are a few easy steps you can take to restore the security of your uPVC door.Whether it’s realigning the lock or cleaning the locking mechanism These simple fixes can increase the security of your home.Clean the LockPatio doors are fantastic for bringing the outdoors in while keeping out the elements. However, they can be risky for security in the event that the lock isn’t working properly. Over time, wear and tear, cold and hot weather dirt and debris can take their toll on your patio door’s lock and make it difficult to open. With a little effort, you can make sure that your patio door’s lock always works properly.It’s crucial to clean the lock of your patio door and all its moving parts. This will help remove any dirt or coatings that may be preventing your lock from functioning correctly. Start by wiping down the moving parts of the lock for your patio door with a damp cloth, then employ a scouring pad or rough damp cloth to scrub any hard-to-reach parts of the door and frame that are ingrained with dirt. Then, wipe the entire lock with a dry cloth to remove any remaining dampness, and allow it to air dry prior to using it again.If your patio door has pin-tumbler latches, you can apply powdered graphite to the key. You can also apply a Teflon lubricant like WD-40 Multi Use Product. This type of lubricant can be easy to apply, and it won’t disintegrate as time passes. If you’re unable to locate a suitable lubricant you could use a pencil with a thick tip. Put the pencil into the lock and jiggle it around a bit to distribute the graphite.Tracks for sliding patio doors require regular maintenance to ensure that they’re free of dust, dirt, and debris. They are particularly vulnerable to snow and ice, which can cause them become stuck or slack, making it harder for your patio doors to open and close.You can clean the track rails and rollers on sliding patio doors by removing any weather stripping that is damaged or dirty. Clean it and replace it. The same is true to patio door rollers which can be cleaned and sprayed with a non-stick lubricant to help them move freely.Lubricate the moving partsuPVC French doors, like sliding patios, are operated using 3 to 4, or sometimes, 5 point locking mechanisms. These include the handle and lock cylinder that is operated with a key. These doors also need maintenance, and specifically lubrication of the moving parts. This can be accomplished with the use of a thin oil but not WD40. It should be done at least once per year.If sagging hinges aren’t the cause, the door may be misaligned and caught or rubbing against the strike plate’s hole in the frame. Take off the strike plate and employ a sharp tool expand its mortise. This allows the latch to fit correctly in the hole, and also prevents getting caught or rubbing against the frame.Measure the length of the cylinder using the help of a piece of book or wood that is able to fit into the space above the adjustment screw. The outer dimension is the distance from the outside of the door to the middle of the cylinder, and the inner dimension runs from the center of the adjustment screw to the end of the cylinder.Check the lock’s lengthIf your patio door latch is difficult to turn, even after cleaning and lubricating, there’s a possibility that it’s out of alignment with the strike plate hole. Verify that the door is balanced, and that the hinge screws are tight. In a lot of cases, moving the strike plate upwards or downwards will solve the issue.The latch may not be able to engage properly when the strike of the lock is too small. In this case you’ll have to increase the opening using a chisel or hammer and then test the latch to make sure that it connects to the strike plate in a smooth manner without rubbing against or landing on the door’s frame jamb.Before purchasing a new lock, it is important to identify the type of mortise lock you currently have. You can do this by taking a look at the faceplate of the lock and noting if it is square or round. Then, take a look at the screw holes in the existing lock and note the size of each one. This information will aid you in finding a replacement that is the same width and will fit perfectly into your existing hole.You’ll need to identify the mortise lock and examine it for any scratches, bends, or other damage that need to be fixed. patio door tune-up damaged or bent latch is more likely to break than one that’s been used much, so be sure to replace the lock with a brand new one that is secure if you find any signs of damage or wear.After you’ve determined the type of lock replacement you require It’s time to start the actual repair. The old spindle and handle must be removed from the patio door. Introduce the new handle. Begin by installing the handle in the interior and aligning it with the spindle and then securing it in place with the two bolts or screws that secure it. Once the handle’s interior is in, install the handle that is outside and screw it in place as well. After you’ve completed the steps then you can test the new handles to ensure they open and close easily and that the latch locks correctly with the strike plate.Make sure the door’s strike is checkedThe door latch and strike plate are the two parts of the lock that work to ensure the latch secures the door. Misaligned strike plate and door latches will cause the latch to not latch the door in a proper manner. Fortunately, the issue is usually easy to correct.First, examine the holes in the strike plate’s receiving to ensure that they are clear of obstructions like dirt or plastic plugs. Then, loosen the keeper screws that secure the strike plate in place, allowing it to move vertically but not detaching it from the door frame. Adjust the strike plate so that it aligns its holes for receiving with latch hooks of the door latch. After the strike plate has been adjusted then tighten the screws and then test the door to determine whether it shuts easily with the new adjustment.Door strike plates can be a bit difficult to locate for homeowners with sliding patio doors, but they’re crucial to lock and unlock your door. The plates made of metal are located on the top and bottom jambs of the door where they support its latch. The door latch slides onto the strike plate, and it creates an airtight seal. If the strike plate is damaged, rusted or not installed correctly, it may stop the latch from locking the door securely.One common reason for the patio door lock to stick or not close is a misalignment of the latch and the strike plate. This can be confirmed using the “lipstick” test. Rub some lipstick along the edge of the deadbolt and then cover it with masking tape. When you shut the door, the lipstick will leave marks on the tape, showing you exactly where the latch contacts the strike plate. If the mark is too low or high it is possible to alter the strike plate.If your patio door locks for sliding are not working properly, they can keep your home safe from burglars. You must repair the issue as soon as you can. Follow these easy steps to repair your patio door lock and restore it’s functionality.