cwysx61@erus1.sarahconner.co.uk – https://www.repairmywindowsanddoors.co.uk/patio-door-repairs-peterborough/

Patio Doors Repair – How to Fix a Wet Dog and Save Your Dog From Cold, Wet FeetPatio doors can provide a convenient and comfortable transition between your outdoor and indoor space. By keeping the air inside your home, they could help you save money on heating or cooling costs.Over time, the luster of your sliding glass or French door may fade. Simple repairs can keep your sliding glass or French doors looking and working like new.WeatherstrippingIt’s 5 AM and you’re letting your dog out for his morning jog when you step into a puddle of water right near the sliding patio doors. You look around and realize that the rain from last night blew through the seals of your patio doors. This isn’t going to be an easy project. However, with a little patience and a few tools to fix the issue, you’ll be able to do it and protect your dog from wet, cold feet.The most important thing is to replace the weatherstripping, which seals the gap between your door and the jamb, which prevents the entry of pests, drafts and moisture. This will also help keep your energy costs down. If you check your windows and door, you can determine if the weatherstripping needs to be replaced or not.There are several types of weatherstripping available that include open-cell and felt foam, vinyl and thermoplastic rubber, as well as metals like bronze or copper. Each type has its advantages and disadvantages. Foam with open cells and felt are both inexpensive, but they tend to be ineffective and visible when blocking airflow. Vinyl is more expensive but it holds up well and is resistant to moisture. Rubber is an excellent choice for areas with high traffic because it doesn’t wear out as quickly.To install new weatherstripping, first remove the patio door from the frame by loosening the roller adjustment screws using a screwdriver. Then, using a flathead screwdriver, loosen the plugs that hold the weatherstripping to the bottom of the frame. Remove the weatherstripping that was previously installed from the frame and clean any adhesive residue. Then, cut the new to the appropriate length, peel back the plastic strip at the other side and attach it to the jamb with the putty knife.Reinstall the door, and adjust the roller screws to ensure it is properly seated in the track. Apply waterproof caulk to the place that the stationary panel passes through the sliding door and the edge of the stationary panel meets the frame. This is a less-reliable seal than the weatherstripping, however, it should last for a few days.Locks and handlesLocks and handles for patio doors are crucial to the security of your home. Over time they can be damaged or worn out and need to be replaced. In addition, the spindle that connects the interior and exterior handles could also require to be replaced.To replace the handle on a patio door, remove the old one first by dislodging any screws that held it in the place. After removing the handle, you can use a level to ensure that the patio door is straight. If the door isn’t straight it can interfere with the lock. This could lead to problems in the future.Once you have the new handle Close and open it a few times to ensure it works correctly. If you encounter any issues you are having trouble, contact the manufacturer or a hardware expert for assistance. To prevent future problems it is a good idea to also lubricate your lock mechanism with silicone-based lubricant.The most popular patio door lock is the mortise latch. Repair My Windows And Doors is usually made of steel and fits inside a pocket that has been cut into the frame of the door. These locks are typically used on sliding wood and aluminum doors. When replacing a mortise lock, it is important to take a few measurements before purchasing a new lock. The measurements you need to take include the locations of the mounting holes as well as the location of the keyway inside the lock.Some handles for patio doors are equipped with a locking mechanism built into the handle. The handles have an elongated key cylinder that can be inserted into the handle’s keyway. If you have this type of patio door both the outside and inside locks are combined into one. This type of patio doors is typically found on sliding aluminum doors.If the latch on your patio door doesn’t stay latched, the lock tongue may not be catching the hasp in the right way. Another possibility is that the sliding door isn’t completely parallel to the jamb on the side. The door should be opened by about an inch, then place it against the frame. This will reveal if there is a gap between the jamb and the door. If there is, adjust the rollers on the left or right sides of the patio door to get it perfectly parallel with the jamb.MisalignmentAs time passes, the door’s tracks and rollers can lose their proper alignment. This could cause the door to stick or become difficult to move. It could also allow cold air and drafts to be able to enter your home, which can decrease energy efficiency. Misalignment can be easily fixed and prevented. Simply applying a silicone-based oil to the tracks and rollers will make your doors glide smoothly once again. This is a good option in order to keep your doors operating at their peak.A damaged screen could also be a problem. It can be an inconvenience or even an issue. It can also prevent the doors from closing and opening properly, causing energy loss. In some cases the damaged screen can be repaired, however in other cases, it’s best to replace the entire door. If you’re experiencing a ripped screen, clean it thoroughly and be sure to avoid turning the handles of the door the wrong way when closing and opening.Over time, hinges can become loose due to normal wear and tear or use. This can be corrected by tightening screws frequently. This is a simple task which you can perform yourself, but if not comfortable doing it, you should consult a professional to ensure your doors are correctly aligned and secure.It’s recommended to regularly clean your patio doors track and rollers. A simple brushing or vacuuming will remove dust and debris that could hinder the smooth operation of your patio doors. You can use a special tool to remove tough dirt or corrosion. It is possible to fix any misalignment by tightening, or examining the screws. Sometimes, it is necessary to replace the hinges to ensure a long-lasting seal.If your patio doors’ frames are sagging or warped they could affect their alignment and performance. The shifting or warping could be caused by foundation issues, however, it can also result due to poor installation or regular use. A professional can repair or replace the frame of your patio door and ensure that it is properly aligned so that it can function at its best.RollersThe sliding patio doors are ideal for bringing the outdoors in and let in lots of light, but they need some care to ensure they are running smoothly. If you have to yank the handle hard to get the door to move or it doesn’t move as smoothly as it used to, it could be the rollers. Over time the lower track may become clogged with dirt, dust, and mud. This makes it difficult for rollers to move. You can clean it up and spray it with a lubricant such as 2Slick to determine if it helps.If the tracks have been cleaned but the rollers aren’t gliding freely, then it is time to replace them. There are a variety of replacement rollers available to match your door and the type of track you have. You can find them at a variety of hardware stores however you will need someone to assist you in the removal and replace the rollers. Take a photo of the rollers installed within the frame to help the experts identify the exact type and model you require. You can also search for features that can be identified, such as dimples or bumps, cutouts or flared edges to narrow down the replacement options.When the rollers are replaced, you’ll need to reinstall the sliding door back into its frame. This is a heavy door, and you might need some help. Start by checking to make sure there aren’t any screws securing the track in the frame on either side of the frame and that they are loose enough to allow the door’s bottom to drop into the channel on the top of the frame. Remove the screen door from the opening. Make sure it’s free of the track rollers, track and track.Once the new rollers are installed, carefully insert the door into the frame, then swing it into place. If your new rollers are adjustable you can adjust them to allow the door to move to the extent it requires.